Eagle Tree Systems MicroVector Package w/GPS
Eagle Tree Systems MicroVector Package w/GPS
Whether you’re into FPV racing, freestyling, or serious camshipping, the MicroVector (µV) integrated Flight Controller and OSD should be perfect for your small FPV mulitrotor or fixed wing model! VikingUAS has made it simple with a one stop shop for this product no more guess work everything you need to get up and running included in this one PACKAGE….
We consider this a Made to Order product allow for 7-10 days shipping….
Built in OSD with COLOR GRAPHICS and fully customizable screens
Programmable video power control: Turn on/off your video camera and/or video transmitter using a radio switch, on arm/disarm, etc.
SkyGates Virtual Racing (Experimental Augmented Reality, Optional GPS required)
Built in Flight Data Recorder/data logger helps take out the guesswork if something goes wrong
Fully set up and tune your µV three convenient ways:
OSD stick menus at the field
Optional InfoPanel LCD
Fast 32 bit microcontroller
DMA enhanced control loop running at up to 8 kHz
Advanced PID and filter tuning from either the GUI, or stick menus at the field
Oneshot and Multishot ESC Protocols
Standard 30.5mm mounting hole centers
PWM, SPPM, Spektrum Satellite and S-BUS Receivers supported, with 4 types of RSSI
BLHeli ESC configuration via the µV USB port
Compatible with most PDBs, including those with built in current sensors (or use our PSU)
Multirotor airframes: Racing Quadcopter, Standard Quadcopter, Tricopter, Y6, Hexacopter
Fixed wing airframes: Traditional, Elevon, V-tail
Add our dual band GPS module for advanced GPS flight modes, RTH, and waypoints
Antenna tracking and laptop position display available with our EagleEyes FPV Station
Other accessories include 12V/5V PSU/Current Sensor (using this cable), Alerter LED/Buzzer, Pitot tube for Airspeed, and InfoPanel LCD Display
UART for telemetry, including ET Open Telemetry, DragonLink, and Taranis (pigtail cable included)
µV with plastic case (4 screws)
Set of 5 rugged "pigtail" cables for precise installation
The GPS/Magnetometer V2 simultaneously receives and monitors both GPS and GLONASS satellites, in addition to other improvements, which can provide the following benefits:
Improved position accuracy for more precise hovering and tracking
Improved RFI rejection – especially with noisy video transmitters and cameras
Faster fix time
Up to 24 satellites in view
The GPS/Mag V2 is compatible with all Vector systems, after firmware update. Vector software version 11.78 or higher is required for correct GPS V2 operation.
Dimensions (L x W x H, approximate): GPS/Mag: 35mm x 24mm x 15mm
Weight: GPS/Mag: 13g
Tired of using multiple batteries, LC filters, BECs, etc.? The Vector's current sensor/PSU makes it super easy to power your equipment.
The current sensor is available with Deans, XT60, or wire leads.
The high efficiency, low noise PSU accepts up to 6S voltage input, and provides filtered 12V and 5V output at 1.5A max per channel. It's perfect for powering most FPV gear, and also powers your receiver on multirotors with “opto” ESCs, eliminating the need for an external BEC.
Note that the 12V regulator does NOT boost the voltage, like a SEPIC. However, the Vector's 12V PSU has a unique Low Voltage Loss feature that drops the regulator’s output by only about 0.5V if you are using a 3S pack operating below 12.5V. For example, if your 3S pack is at 11.5V, the regulator outputs about 11V. Other non-boost switching regulators typically drop the output voltage by 1.3V or more.
In addition, SEPIC and other voltage boost regulators are generally much less efficient and generate much more UHF band noise, and in many cases you don’t need one. All known cameras and many transmitters will operate well across the 3S voltage range. Check your transmitter manual’s specs to determine this. If your transmitter does need a boost when operating at the lower end of 3S, a JST equipped boost regulator can easily be connected into the Vector's AV harness without needing to cut wires.
Wiring Made Simple!
The Vector's filtered PSU and innovative wiring harness (so innovative we're not showing it for a little longer J) makes it easy to connect your 5V or 12V cameras and transmitters without keeping an electrician on standby. If your camera and transmitter+- has have servo style connectors already, you just need to plug them into the labeled plugs, select the appropriate voltages, and away you go. And, If you prefer to use 2 or even 3 flight batteries, additional filters, voltage boosters, etc., that’s trivial to do without needing to do any rewiring. The harness also makes it easy to move the Vector from model to model without removing all of the wiring as well.
1x Vector Current Sensor (PSU)